在操作過程中,請勿對混泥土攪拌車進行維修或潤滑。
Do not repair or lubricate the concrete mixer during operation.
定期在每個注油嘴中添加黃油,每4小時潤滑軸端密封油一次,每周排干一次。
Add butter to each oil filler regularly, lubricate the shaft end sealing oil every 4 hours and drain it once a week.
使用混泥土攪拌車后,根據需要在每個潤滑點添加所需的潤滑劑。
After using the concrete mixer, add the required lubricant at each lubrication point as required.
混泥土攪拌車減速器的齒輪和軸承通過齒輪旋轉將油分散到油箱的內壁,并流入軸承進行潤滑。變速箱油位保持在燃油表的兩條線之間。油位過高或過低都會導致每個組件的溫度升高,潤滑不良,功率損耗增加以及機器故障。
The gear and bearing of the reducer of the concrete mixer disperse the oil to the inner wall of the oil tank through gear rotation and flow into the bearing for lubrication. The transmission oil level is maintained between the two lines on the fuel gauge. Too high or too low oil level will lead to the temperature rise of each component, poor lubrication, increased power loss and machine failure.
用混泥土攪拌車選擇的潤滑劑不得具有特定的粘度和粘度,溫度特性,低凝固點,良好的氧化穩定性,機械雜質和濕氣,耐腐蝕,耐磨材料,其質量指標符合標準。
The lubricant selected by the concrete mixer shall not have specific viscosity and viscosity, temperature characteristics, low freezing point, good oxidation stability, mechanical impurities and moisture, corrosion-resistant and wear-resistant materials, and its quality indicators shall meet the national standards.
自動上料攪拌車在使用的時候應該做好防護,因為它是長期暴露在外面,所以使需要做好防護的,根據我們的經驗我們可以了解到漆面出現損傷的情況是非常多的,就讓我們來做一個簡單介紹:
The automatic feeding mixer truck should be well protected when in use, because it is exposed to the outside for a long time, so it needs to be well protected. According to our experience, we can understand that there are many cases of paint damage. Let's give a brief introduction:
自動上料攪拌車
Automatic feeding mixer
一、淺劃痕:由于摩擦及日常護理不當,漆面出現輕微的劃痕,但并未露出底漆,這種劃痕在陽光下比較明顯。一般通過拋光方法去除。
1、 Shallow scratch: due to improper friction and daily care, there are slight scratches on the paint surface, but the primer is not exposed. This kind of scratch is more obvious in the sun. Usually removed by polishing.
二、褪色:大氣中的油煙和污染物是造成車漆變色、褪色的主要原因。褪色與氧化不同,發生褪色時,車漆會出現不均勻的色差。中、輕度的褪色可用研磨、拋光治理,嚴重時重新噴漆。
2、 Fading: oil fume and pollutants in the atmosphere are the main reasons for the discoloration and fading of car paint. Fading is different from oxidation. When fading occurs, the paint will have uneven color difference. Moderate and mild discoloration can be treated by grinding and polishing, and repaint in case of serious discoloration.
三、水痕紋:水痕紋是水滴蒸發后留下的痕跡,呈環狀。氧化、常用洗滌靈清洗的車容易染上水痕。
3、 Water mark: water mark is the mark left by the evaporation of water droplets, which is circular. Cars that are oxidized and commonly cleaned with detergent are easy to get water marks.
四、漆面氧化:在太陽紫外線的照射下,漆膜會不斷向空氣中蒸發油份以達到保護自身的作用,長時間就會導致漆面油分的過分散失。漆面的亮度都大打折扣,使漆面慢慢發白,形成氧化層,縮短了車漆的壽命,氧化嚴重的話可以通過研磨和拋光來處理。
4、 Paint oxidation: under the sun's ultraviolet radiation, the paint film will continuously evaporate oil into the air to protect itself, which will lead to excessive loss of paint oil for a long time. The brightness of the paint is greatly reduced, which makes the paint white slowly and forms an oxide layer, which shortens the service life of the car paint. If the oxidation is serious, it can be treated by grinding and polishing.
五、蝕痕:蝕痕是面狀磨蝕。昆蟲、鳥糞、樹汁、焦油、瀝青都有可能引起的蝕痕。輕微的蝕痕可用研磨拋光來。
5、 Etch marks: etch marks are surface abrasion. Insects, bird droppings, tree sap, tar and asphalt may cause corrosion marks. Slight corrosion marks can be solved by grinding and polishing.
以上就是自動上料攪拌車表面經常遇到的一些情況,希望大家啊要做好防護,定期的學習表面養護的知識,經做好防水處理,就會減少自動攪拌車
The above are some situations often encountered on the surface of automatic feeding mixer truck. I hope you should do a good job in protection, regularly learn the knowledge of surface maintenance, and reduce the number of automatic mixer truck after waterproof treatment
本文的精彩內容由自動攪拌一體車知識提供,本網站還有很多的精彩內容,更多的內容您可以點擊進入:http://842233.cn我們有專門的客服為您解答問題
The wonderful contents of this article are provided by the knowledge of automatic mixer. There are many wonderful contents on this website. You can click to enter more contents: http://842233.cn We have special customer service to answer your questions